So close yet so far

Finally, the End of all things.

I just need people to know that they didn’t fake the moon landing, that really happened. They faked the moon. It didn’t exist prior to the 1960s when it was created by the US government in order to move the goalposts in the space race.

The insider knowledge that there would soon be a moon to land on gave NASA the head start they needed on the Apollo program to finally beat the Soviets, who were thoroughly blindsided by the sudden appearance of the moon.

Hey I just saw your update! I’m glad you’re getting better results, but like you mentioned, something is definitely still wrong. I’m still pretty convinced your nozzle is clogged, even though it’s new, and I’ll do my best to explain why!

To start, if your printer wasn’t working normally before you printed in wood, I’m totally wrong about everything below and you can stop reading here!

If your printer was working normally before you tried printing in wood though, that means the e-steps were already calibrated correctly, and they wouldn’t need to be re-calibrated after replacing the hot end. If you had replaced the extruder and it started acting this way, that would be a good reason to re-calibrate the e-steps, but replacing the hot-end shouldn’t have had an impact. After swapping an extruder, you calibrate e-steps to basically teach the printer how to extrude the correct amount of filament in the real world again since the new extruder might have different specs from the original and the printer has no way to know something has changed. A hot-end swap doesn’t necessitate recalibrating e-steps though because the extruder is the same and it’s still going to be pushing the same amount of filament through the printer.

If your nozzle is clogged and you recalibrate the e-steps, the measurements you take will be off since the printer can’t push filament through at the rate it should be able to. Your new benchy looks better than before, but that could be because the higher e-steps you calculated mean the printer is now forcing more filament past the blockage by working the extruder more. It’s been calibrated to compensate for the fact it can’t push filament through fast enough, but it’s working harder to do this and it will severely limit its speed before it starts underextruding again. I’m guessing this is the reason for the 3 hour long benchy at 20mm/s? You shouldn’t need to be at 220 C to get PLA to print at 20mm/s from a 0.4mm nozzle either.

Not all nozzles or hotends are well-made or handled with care at the factory. It’s totally possible you got one that shipped with some sort of tiny unnoticeable debris inside that worked its way down into the nozzle as the filament pushed it along. I have a cheap bag of 0.4mm nozzles that have metal shavings stuck in some of them and your first benchy is exactly what my prints look like when I use one of them. If possible, I still recommend changing the nozzle before doing anything more expensive like replacing the extruder. You’ll probably need to set the e-steps back to what they were before changing them though, otherwise you’ll be extruding too much filament if the new nozzle isn’t clogged and the old one is.

I thought the electric version looked exactly the same

Ugly looking things, but so is the LLV. The design is already growing on me, and I guarantee that after a few years on the road, they’ll become just as iconic as the LLV.

This is the first time I’ve even heard the idea of Japan being a “liberal paradise”. I thought it was widely know Japan was super conservative.

What a pleasant shift in mood here from the last debate. The general outlook here was grim after last time, but it’s actually positive now.

What does it do?

B I G S C R E E N

Well, if Peter says it is, everyone should give up on it right now.

Wow I just looked it up and that is the worst design I’ve ever seen. That’s a ton of work just to replace one of the most commonly changed parts.

The fact it won’t print below 220° makes me think it’s a problem with your hotend, and my best guess is that your nozzle is clogged. The higher temperature might be helping the extruder to squeeze a bit of filament around the clog, but not enough.

Changing the nozzle is quick and easy, and most printers come with a spare or two, so I would give that a shot before diving too deep into diagnostics.

I just think most forms of wine have a very unpleasant taste.

For Samsung at least, tapping the dot will tell you what’s accessing what. I can’t confirm if it works on other flavors of Android unfortunately.

Tim Burton is the most Glowworm Beetle director I’ve ever seen.

Pull open quick settings and tap the dot.

It’s upset

I looked into it a bit and it actually is! It’s called Ethereal White Persians

Chihuly?